|This item qualifies for FREE Ground Shipping in the 48 contiguous states!|
For a Limited Time receive 2 5.5" Red Soft Wax Pads and Mike Phillips’ The Complete Guide to a Show Car Shine Paperback Book FREE with your purchase of this kit! Retail Value $33.97.
Not too gentle, not too strong…XMT #3 is just right.
The Pinnacle XMT Porter Cable 7424XP Intermediate Swirl Remover Kit is tailored to the needs of older vehicles with moderate paint imperfections. At the center of this kit is XMT Intermediate Swirl Remover, a midlevel swirl remover with the right balance of abrasives and lubricants to correct and protect the paint at the same time.
The Pinnacle XMT Porter Cable 7424XP Intermediate Swirl Remover Kit eliminates moderate swirls, mild oxidation, and most scratches with the help of the Porter Cable 7424XP. This kit takes a graduated approach to paint correction that leaves paint absolutely flawless.
This kit includes Lake Country’s CCS Dual Action 6.5 inch Smart Pads™ Foam Pads. These flat full contact buffing pads work with your dual action polisher to correct automotive paint more easily than ever before. The CCS Smart Pads™’ user-friendly features provide better control, less product waste, and a more successful detail.
The kit includes:
||Porter Cable 7424XP Variable
The Porter Cable 7424XP Dual Action Polisher is a beefed up, more powerful version of our most popular dual action polisher. The Porter Cable 7424XP Dual Action Polisher has all the user-friendly features of the original Porter Cable 7424, but a 4.5 amp motor enables enhanced performance and durability. The Porter Cable 7424XP Dual Action Polisher operates from 2,500 OPM to 6,800 OPM to provide a faster removal rate. The 7424XP features all ball and roller bearing construction with spiral/bevel gears and an improved switch design. The buffer accepts a 5/16-24 spindle thread. The pad diameter is 6 inches. The polisher includes a wrench, side handle, polishing pad, and a operating manual.
||Dual Action 5” Flex Backing
With hook facing, this plate allows you to switch pads quickly and continue
polishing. A recessed edge and flexible urethane construction gives your
paint extra protection from run-ins with the backing plate. Strict
tolerances on weight, balance, roundness, and flatness ensure consistent
performance time and time again. The backing plate has a 5/16 inch thread.
||12 oz. XMT Intermediate Swirl
Precisely milled abrasives – and a lot of them – blend away moderate to
severe blemishes without removing significant layers of clear coat.
Since clear coats are extremely thin, these Concentrated Micro Abrasives
preserve as much of the paint as possible while removing only the defect.
The abrasives gradually diminish as they work, giving you a built-in
finishing polish. The paint will experience little or no loss of
surface gloss. Use XMT Intermediate Swirl Remover for all-over paint
correction or as a spot treatment for problem areas.
||12 oz. XMT Ultra Fine Swirl
This polish is made with such small abrasives that you can’t see them with
the naked eye. The sheer number and minute size of the abrasive particles
blend away fine flaws in the clear coat without leaving any trace of surface
marring or haze. Just like a fine jeweler’s rouge, XMT’s Concentrated
Micro Abrasives leave the paint finish glossy and smooth, just like new.
XMT Ultra Fine Swirl Remover is for like-new paint that is just starting to
show signs of age. It can also be used as a finishing polish.
||12 oz. XMT Carnauba Finishing
The gentle cleaners blend away minor flaws - like spider webbing, haziness,
and overall dullness – to increase depth and clarity. At the same time, a
layer of carnauba bonds to the paint surface to further enhance the dynamic
shine created by the glaze. What can’t be removed with the cleaners is
filled in with carnauba to create a smooth, flawless finish. Its
perfection and protection in one! Use XMT Carnauba Finishing
Glaze as the finale to your detailing process. To increase depth and
brilliance, top the glaze with Pinnacle Signature Series II.
||1 CCS Orange 6.5 Inch Light Cutting
Firm, high density foam for scratch and defect removal. Use this pad with
polishes and swirl removers. It’s an all around pad that will work on most
light to moderate imperfections.
||1 CCS White 6.5 inch Polishing
This high absorption foam formula is intended for the application of waxes,
micro-fine polishes and sealants. This pad has very light cutting power so
it’s perfect for pre-wax cleaners.
||2 CCS Gray 6.5
Inch Finishing Foam Pads
Least abrasive. Composition is firm enough to withstand added pressure
during final finishing to remove buffer swirls. Use with machine glaze or
finishing polish. Ultra-soft and incredible for a putting on that finishing
||2 Microfiber Towels (16 x
These microfiber towels are spun from an 80/20 polyester/polyamide blend,
producing a highly refined microfiber. The microscopic polyester/polyamide
fibers are split with a unique process that creates a "feathered" weave on
one side for buffing and looped fibers on the other side, which are
excellent for cleaning. This superior “feather” weave results in far greater
absorption properties in a virtually lint free network of fibers.
||1 Polish ‘N Wax Applicator
This two-sided applicator is an excellent tool for cutting in close around
trim and mirrors, places that your polisher can’t go. The foam applicator
has gray finishing foam on one side and orange light cutting foam on the
||12 oz. Pinnacle XMT Polishing
Foam Pad Conditioner
Prevention of dry buffing is as easy as misting an unused pad with Pinnacle
XMT Polishing Pad Conditioner. It only takes a couple of spritzes to prep
the pad for polishing. The rich lubricants instantly penetrate the pad,
softening and conditioning the material. Even if the pad has never been
used, it will glide across the paint like you’re halfway through the detail
All pads included in the XMT Porter Cable Intermediate Swirl Remover Kit have hook & loop backing, which attaches securely to the included 5 inch hook & loop backing plate.
Use the products as follows:
Remove moderate swirls, scratches, and oxidation to restore a like-new gloss and depth with the Pinnacle XMT Intermediate Swirl Remover Kit.
- Prep pads before polishing with Pinnacle XMT Polishing Pad Conditioner. On significant swirls and flaws, apply XMT Intermediate Swirl Remover #3 with the orange pad. If damage is concentrated in particular areas, like the hood and roof, you may only need to apply this product on problem areas. Buff off residue after each section.
- Apply XMT Ultra Fine Swirl Remover #1 with the white polishing pad. You can do an all-over polish to remove the lightest imperfections with this gentle swirl remover. Buff off residue after each section.
- Your paint should be in great shape at this point. Apply XMT Carnauba Finishing Glaze with one of the gray foam pads. Buff off the residue as you complete each section.
- Your vehicle will be glossy and reflective after applying the glaze. For the deepest shine and longer-lasting protection, use the second gray pad to apply your favorite wax. We recommend Pinnacle Signature Series II Carnauba Paste Wax for a fantastic reflection on any color.
- Clean each pad after use with Pinnacle XMT Polishing Pad Cleaner. Spray each pad generously with the cleaner and toss them in a bucket of clean water. Agitate with a Foam Conditioning Brush if necessary. Rinse well and let air dry.
XMT Porter Cable Intermediate Swirl Remover Kit includes:
Porter Cable 7424XP Polisher
5 inch Dual Action Flex Backing Plate
12 oz. XMT Intermediate Swirl Remover #3
12 oz. XMT Ultra Fine Swirl Remover #1
12 oz. Carnauba Finishing Glaze
6.5 inch CCS Orange Light Cutting Pad
6.5 inch CCS White Polishing Pad
2- 6.5 inch CCS Gray Finishing Pads
2- 16 x 16 inch Microfiber Towels
12 oz. XMT Polishing Pad Conditioner
Polish ‘N Wax Applicator
A total retail value of $297.37. SAVE $47.38!
- Additional discounts are not
- Please call for an expedited shipping
quote on this item.1-800-869-3011
|Upgrade to the
Porter Cable 7424XP Dual Action Polisher HD!
The HD model has a heavy duty 16 gauge, 25 foot power cord hardwired into the polisher. The longer cord is more convenient than an extension cord and it is gauged to deliver maximum power to the polisher for safe, efficient operation. (Standard cord is 11.5 ft.)
Select the HD model from the drop-down menu below.
Pinnacle XMT Porter Cable 7424XP Intermediate Swirl Remover Kit FREE SHIPPING
Stars based on
I would recommend this item to a friend.
This is one of the best tools I have ever purchased!
November 8, 2014
My 67 Camaro paint looked great from 3 feet away but in the sun you could see light scratches in the clear coat. It was that way from the time I purchased the car 2 years ago. I checked with a detail shop and they wanted $350 to buff out the paint. I had seen the TV adds about this polishing system but was concerned about using it with no experience. After a year of watching the TV adds I bought the system and watched the video 3-4 times. I just finished the car and it is stunning!
It did take about 40 hours to complete so if you are not willing to invest that much time then this system is not for you. I had to use the # 3 scratch remover 2-3 times on most of the car to get the results I wanted. The #1 scratch remover was a one step process as well as the glaze step. The most important step is to get the down pressure correct and go slow to remove deep scratches. I do not think you could ever hurt your paint with this system if you do what the video says to do.
This is one of the best tools I have ever purchased.
Pros:Great results but will take many hours to complete the job. Works as advertised! Enough polish to do one car with no problem.
Cons:I think the kit should come with the 5.5" pads not the6.5". The smaller pads would get into tight places better.
The cord should be longer as standard.
Would be nice if the speed control had a two button memory. I used 1 and 4.5 most of the time
Decent, but could be better
May 2, 2011
I just spend the last three days straight detailing the exterior of my Jet Black 535i. The previous owner of my car must not own a garage. I had severe water marking/etching that went deep into the clear coat. The final results look good, but the hood/roof/trunk still need more work. Here was my process:
1) Washed car with sea foam, foammaster gun, DP wash, Sonus rim/wheel cleaner, dried with chamois and microfiber towel
2) XMT speed clay over entire car and all glass
3) Taped off the whole car
4) Test spot on hood using XMT #1 fine swirl remover, white pad, and finished with XMT finishing glaze, black pad. Test spot made it obvious I would need something more abrassive.
5) Went over hood/roof/top of trunk THREE differnt time with XMT #3 and orange pad. Started with polisher set to 5 with moderate pressure and ended up with it set to 6 with a lot of pressure. Still need something more abrasive.
6) Went over entire car with XMT #1/white pad
7) Had to again wash entire car as there was powder/dust from the product all over the car.
8) Went over entire car with XMT Finishing Glaze and ran out of time. Will wax tonight with Sovouran Series II.
Now that I'm done, I really wish I would have purchased the "severe" kit instead of the intermediate. Not because I have a lot of swirls, but to get rid of the deep water stains/acid rain spots eatting into the clear coat on the top of my car. Overall I recommend the product. Rest assured this is extremely safe and will not ruin your finish. I had the Porter maxed with hard pressure, orange pad, and a liberal amount of #3 swirl remover....
Not as advertised
February 21, 2009
Okay, this stuff does make a difference, but it does NOT produce perfect results as advertised. After hours on end trying to get the results I want, I'm going to be moving on to something else.
April 7, 2008
I had some severe water spots along with some bad swirl marks that I could not remove. Well, I followed the video step by step and she looks like new again. For minor swirl marks and scuff marks you can skip the orange pad & #3 and just use the white or gray pad with the #1 ultra fine product. Works like a charm, highly recommended!